Mon, 13 Apr 2026 12:54:38 +0000 <![CDATA[Nieuwste producten van Fiammhorns.com]]> https://www.fiammhorns.com/ <![CDATA[Fiamm Jericho 2 Blade | PTC Ø6mm]]> FIAMM Jericho 2 Blade / PTC Ø6mm
(FIA928060Z)
The FIAMM Jericho Air horn is a compact truck air horn for professional use.
Air horn with a built-in electronic valve for trucks and buses.

Fiamm offers several variants of this type of horn, where both the electrical and pneumatic connections differ.

This Jericho is equipped with a two-pin electrical connection and a Push to Connect fitting for Ø6mm air hose.

Delivery:

1x Jericho Air horn
 
Productinfo
Material PA66 , Steel
Measurements (HxWxL) 20cm x 12,5 cm x 9,5cm
Weight 390 gr.
Voltage 24v
Ampere 0,8 A
Air Pressure (Bar) 4-8 bar (amount of pressure influences dB's)
Soud Pressure (at 2m) 118 dB
Fiamm Code 928060Z
Connector Type: Two Poles / Blades
Air Connection Ø6mm tube (Push To Connect)
EU-Registration 10 ECE
28 ECE
Made In Italy
HS Code 85123090
 
 
Attention:

1. For this horn you need air on board. This must produce at least 4bar - 8bar pressure.

2. For this horn you need a 24V electrical power supply on board.
]]> Fri, 27 Mar 2026 10:34:28 +0000 <![CDATA[Spain | Emergency 24v (Pneumatic)]]> MC4-FD-24V / TA/2-LE-V (921117-920400)
 

Pneumatic Priority Siren for Spanish priority vehicles, such as ambulances and fire brigades.

Complete set consists of an air compressor and air horns. Also availlable without air horns.
 
Basic Technical Info
Voltage 24Vdc
Ampere 8
Decibels at 2m
Air Horn option:
TA/2 LE-V  : 117 dB
 
Frequency
466 - 544 Hz
 
Weight
compressor: 1200 gr.
lubricator: 247 gr.
air horns: 790 gr.
 
Type Approval Homologation Spain
Product Codes Compressor: 921117
Air horns: 920400
]]> Fri, 20 Mar 2026 10:16:48 +0000 <![CDATA[FIAMM Ultimate Blast 12v]]> Fiamm Ultimate Blast 12v
Fiamm compact air horn.
The Ultimate Blast is especially developped as an air horn that can fit in tight spaces under the bonnet. The Fiamm ultimate blast is a double toned air horn and compressor in one.
As cars become more compact and the space under the bonnet is used more efficient by manufacturers, it becomes harder to fit an extra pair of airhorns.
Because of it's compact design it is easier to find a place for it.

The Ultimate blast air horn is availlable in 12v]]> Thu, 12 Mar 2026 19:45:31 +0000 <![CDATA[6mm-1/8 BSPT knee coupling]]> Knee coupling PTC for 8 millimeter tube to 1/8 BSPT (Conical)
With PTC connection for 8 mm tube and 1/8 BSPT male thread.

The external thread is conical and taped.
The housing of the coupling is nickel-plated brass.

So you can screw this right-angled coupling into a 1/8 BSP input and connect an 8 millimeter tube to it.

This coupling can be used simply by pushing the hose into the end of the coupling until it is firmly secured in place. The hose can be easily removed by pushing the ring back towards the coupling and pulling the hose out.

Abbreviations:

PTC: Push To Connect.
8mm tube: Outside diameter of the tube is 8 millimeters.
BSPT: British Standard Pipe Taper, also called Gas Thread. (Taper = conical)
Conical: Tapered, or sloping.

More information about hose sizes and threads can be found here: About Threads]]> Thu, 12 Mar 2026 08:09:26 +0000 <![CDATA[10mm-1/4 BSPT knee coupling]]> Knee coupling PTC for 10 millimeter tube to 1/4 BSPT (Conical)
With PTC connection for 10 mm tube and 1/4 BSPT male thread.

The external thread is conical and taped.
The housing of the coupling is nickel-plated brass.

So you can screw this right-angled coupling into a 1/4 BSP input and connect an 10 millimeter tube to it.

This coupling can be used simply by pushing the hose into the end of the coupling until it is firmly secured in place. The hose can be easily removed by pushing the ring back towards the coupling and pulling the hose out.

Abbreviations:

PTC: Push To Connect.
10mm tube: Outside diameter of the tube is 10 millimeters.
BSPT: British Standard Pipe Taper, also called Gas Thread. (Taper = conical)
Conical: Tapered, or sloping.

More information about hose sizes and threads can be found here: About Threads]]> Thu, 12 Mar 2026 07:19:23 +0000 <![CDATA[Pneumatic Splitter for 10x7mm tube]]> Y-connector (splitter)
Suitable for air hose with:
Outer diameter: 10 mm
Inner diameter: 7 mm

This Y-connector is used to split an air line from one hose to two air horns, allowing both horns to emit a signal simultaneously.
The Y-connector can be easily installed by sliding the hoses over the connections. All three sides feature a so-called hose nipple (or hose barb). For added security, the hoses can be secured with hose clamps.]]> Thu, 05 Feb 2026 15:43:01 +0000 <![CDATA[6mm-1/2 BSPP straight coupling]]> Straight push-in fitting for 6 mm hose with O-ring
With PTC connection for 6 mm hose and 1/2 BSP male thread with O-ring.
The male thread is straight and equipped with a sealing ring. The fitting housing is made of nickel-plated brass.

You can screw the fitting into a 1/2 BSP inlet and connect an 6 mm hose to it.

This fitting can be easily used by pushing the hose into the end of the fitting until it is securely in place. The hose can be easily removed by pushing the ring back toward the fitting and pulling the hose out.

Abbreviations:
PTC: Push To Connect.
6 mm hose: Outer diameter of the hose is 6 mm.
BSPP: British Standard Pipe Parallel, also known as Gas Thread. (Parallel = straight)
O-ring: Rubber sealing ring
NBR: Nitrile rubber
 ]]> Mon, 26 Jan 2026 07:28:31 +0000 <![CDATA[12mm knee coupling ]]> Right angle connection piece for 12mm to 12mm tube.
With PTC connections for 12 mm and 12 mm tube.

The housing of this connecting piece is largely made of plastic.

With this connection piece you can connect 12mm hose to 12mm hose at a 90 degree angle.

This coupling can be used simply by pushing the tube into the ends of the coupling until it is firmly secured in place. The hose can be easily removed by pushing the ring back towards the coupling and pulling the tube out.

Abbreviations:

PTC: Push To Connect.
12mm hose: Outside diameter of the tube is 12 millimeters.

More information about hose sizes and threads can be found here: About threads]]> Wed, 24 Dec 2025 15:04:04 +0000 <![CDATA[12mm-1/2 Knee Coupling]]> Angled plug-in coupling for 12 millimeter air tube
With PTC connection for 12mm hose and 1/2" BSP and NPT male threads.

The male thread is short and tapered, allowing the coupling to be screwed into both BSP and NPT inlets. For a secure seal, the coupling is equipped with a sealing ring.
The coupling housing is made of brass with an NBR O-ring.

You can screw this coupling into a 1/2" BSP or NPT inlet and connect a 12mm air tube.

This coupling is easy to use by pushing the hose into the end of the coupling until it is firmly in place. The tube can be easily removed by pushing the ring back toward the coupling and pulling the hose out.

Abbreviations:

PTC: Push To Connect.
NPT: National Pipe Thread, thread primarily used in the US.
BSP: British Standard Pipe, also known as "Gas Thread."
12mm hose: The outside diameter of the hose is 12 millimeters.
O-ring: Rubber sealing ring.
NBR: Nitrile rubber.

More information about hose sizes and threads can be found here: About Threads


 ]]> Wed, 24 Dec 2025 14:41:53 +0000 <![CDATA[10mm-1/2 Knee Coupling]]> Angled plug-in coupling for 10 millimeter air tube
With PTC connection for10mm hose and 1/2" BSP and NPT male threads.

The male thread is short and tapered, allowing the coupling to be screwed into both BSP and NPT inlets. For a secure seal, the coupling is equipped with a sealing ring.
The coupling housing is made of brass with an NBR O-ring.

You can screw this coupling into a 1/2" BSP or NPT inlet and connect a 10mm air tube.

This coupling is easy to use by pushing the hose into the end of the coupling until it is firmly in place. The tube can be easily removed by pushing the ring back toward the coupling and pulling the hose out.

Abbreviations:

PTC: Push To Connect.
NPT: National Pipe Thread, thread primarily used in the US.
BSP: British Standard Pipe, also known as "Gas Thread."
10mm hose: The outside diameter of the hose is 10 millimeters.
O-ring: Rubber sealing ring.
NBR: Nitrile rubber.

More information about hose sizes and threads can be found here: About Threads


 ]]> Wed, 24 Dec 2025 14:32:27 +0000 <![CDATA[Reducing Nipple 1/8 BSPT to 3/8 BSP]]> Straight adapter (female) from 1/8 BSPP to 3/8 BSPP.
Adapter (female) from 1/8 BSPP to (female) 3/8 BSPP.

The internal thread is straight.
The adapter housing is made of nickel-plated brass.

You can screw in a 1/8 BSPP male thread on one side and a 3/8 BSPP male thread on the other side.

Abbreviations:
BSPP: British Standard Pipe Parallel, also known as Gas Thread. (Parallel = straight)]]> Wed, 29 Oct 2025 15:44:05 +0000 <![CDATA[Reducing Nipple 1/4 BSPT to 1/8 BSP]]> Straight adapter (female) from 1/8 BSPP to 1/4 BSPP.
Adapter (female) from 1/8 BSPP to (female) 1/4 BSPP.

The internal thread is straight.
The adapter housing is made of nickel-plated brass.

You can screw in a 1/8 BSPP male thread on one side and a 1/4 BSPP male thread on the other side.

Abbreviations:
BSPP: British Standard Pipe Parallel, also known as Gas Thread. (Parallel = straight)]]> Wed, 29 Oct 2025 15:43:48 +0000 <![CDATA[12mm T-piece to 2x8mm]]> Splitter Ø12mm to 2x 8mm hose
T-piece for splitting 12mm hose into 2x 8mm hose.

The T-piece housing is largely made of plastic and consists of two parts:
  1. A PTC adapter from Ø12mm to Ø8mm hose.
  2. A T-piece with an Ø8mm pin to 2x Ø8mm PTC coupling.

You can use this combination to adapt a hose with an outer diameter of 12mm to 2x 8mm hose.

This T-piece is easy to use by pushing the hose(s) into the PTC ends until they are firmly seated. The hose can be easily removed by pushing the ring back toward the coupling and pulling the hose out.

Abbreviations:
PTC: Push To Connect.
12mm hose: The outer diameter of the hoses is 12mm.
 ]]> Tue, 07 Oct 2025 07:51:31 +0000 <![CDATA[12mm and 8 mm PTC plug-in coupling]]> Straight PTC coupling for 8 and 12mm hoses
Straight adapter for converting 12mm hoses to 8mm hoses.
One end accepts a Ø12mm hose, and the other end accepts an Ø8mm hose.

The housing of the coupling is largely made of plastic.

This coupling is easy to use by pushing the hose(s) into the PTC ends until they are firmly seated. The hose can be easily removed by pushing the ring back toward the coupling and pulling it out.

Abbreviations:
PTC: Push To Connect.
8mm hose: Outer diameter of the hoses is 8 millimeters.
Ø12mm: Outer diameter of the hose is 12mm.]]> Thu, 02 Oct 2025 14:08:00 +0000 <![CDATA[8mm PTC Splitter with Pin]]> Splitter for 2x Ø8mm hoses with Ø8mm pin
T-piece for 2x 8mm PTC hoses. With 1x 8mm diameter pin

The housing of the T-piece is largely made of plastic.

This T-piece is easy to use by pushing two hoses into the PTC ends until they are firmly seated.
On one side, the pin of this splitter can be inserted into an 8mm PTC coupling.

The hose can be easily removed by pushing the ring back toward the coupling and pulling the hose out.

Abbreviations:

PTC: Push To Connect.
8mm hose: The outer diameter of the hoses is 8 millimeters.
Pin: Insert sleeve or pillar specifically for PTC

More information about hose sizes and threads can be found here: thread]]> Thu, 02 Oct 2025 13:16:01 +0000